There are many types of glass, which play an important role in various industries. In addition to the insulating glass and laminated glass used to make doors and Windows, there are many kinds of artistic decorations that we come into contact with everyday, such as hot-melt glass and embossed glass. These glass products have their own characteristics and can be used in various situations. Want to understand the glass door handle replacement method, and how to install the glass door, might as well read it.

一、Replace the glass door handle method

Glass doors are generally made of toughened glass, hardness and reliable, easy to clean and glass doors, generous style, transparent pervious to light, does not affect the light shining, many retail stores are now using the glass door. So the quality at the same time, pay attention to the glass door shake handshandle glass door shake handshandle installation quality will directly affect the beautiful.

1. The handle hole of the glass door on the whole glass door is generally processed when cutting the glass. If the insertion is too loose, the insertion part can be wrapped with soft tape.

2. Before installation, apply a little glass glue to the part of the glass door handle that is inserted into the glass.

3, if it is not glass door tempered glass, with a 10mm glass drill, measure the glass door handle hole distance (to), mark on the glass door, water drilling, installation from the outside first, in the long screw screw handle, pay attention not to leave the handle screw outside.

二、Installation of glass doors

1, the installation of the glass door line, positioning

The fixed glass and movable glass door is combined into a complete glass door, and then according to the requirements of the design and construction drawings, the alignment and positioning are unified, and the position of the door frame is determined.

2, the installation of glass door frame on the top of the limit slot

The limiting slot is 2-4 mm wide and 10-12 mm deep.

3, glass door installation of metal veneer wood base installation

First the square wood fixed on the ground, and then with the plastic will be the metal veneer paste on the square wood.

4. Vertical door frame installation for glass doors

Nail the door frame square wood with the center line, use plywood to determine the position of the door frame column, and then wrap the metal decorative surface.

5. Installation glass for glass door

Use the glass sucker to tighten the thick glass, then lift it up and move it to the position where it needs to be installed.

6. Fixed glass for glass door installation

Nail two small square wood on the bottom of the square wood inside and outside, the thick glass clip in the middle, and then on the square wood coated with tens of thousands of glue, at the same time the metal veneer glued to the square wood.

7, glass door installation of the injection of glass glue to seal

For each gap, such as the top limit slot, the bottom support slot on both sides, thick glass and frame column, etc., inject glass glue to seal it. If there is any excess glass glue, scrape it off with tools.

8. Glass butt joint for glass door installation

Glass door fasteners sometimes need to be spliced due to size, so they should have a width of 2-3 mm on the seam, and then chamfer the edge of the glass plate.

9. Install the spring where the glass door is installed

The floor spring and the door frame top locating pin must be on the same axis after installation.

10, glass door installation above the installation of the lower door clip

Install upper and lower metal door clips on both ends of the glass door leaf respectively.

11. Glass door clamp for glass door installation shall be fixed

Insert small wooden strips into the gaps on both sides of the glass and the door clip and inject glass glue.

13. Handle installation for glass door installation

First, apply the glass glue to the part where the handle is inserted into the glass, and then insert the handle, and then fix the screw when the root is tightly connected with the glass.

14, after the installation, to do the cleaning work.

Relevant concepts

The glass door

        Glass door is a special kind of door, first of all, its thickness is not enough to be a solid door, and it does not belong to the atypical door, in fact, it is a special form of the door. The character of the glass door is determined by the character of the glass itself. When using toughened and transparent glass for example, door leaf has connect appear a function, and when using ground glass, have function of half pervious to light. It is also an event arising from this.